Adaptec SAS RAID Controllers Instalační příručka Strana 16
- Strana / 148
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
2 Sun StorageTek SAS RAID HBA Installation Guide • March 2010
HBA Features
The Sun StorageTek SAS RAID Internal HBA (SG-XPCIESAS-R-INT-Z) has the
following features:
Note – These features are supported by some operating systems but not others. For
more information, refer to the Sun StorageTek RAID Manager Software User’s Guide or
online Help.
■ Flash ROM to update the HBA firmware and BIOS using the BIOS Configuration
utility or the Sun StorageTek RAID Manager graphical user interface (For more
information, see the Sun StorageTek RAID Manager Software User’s Guide.)
■ Disk drive hot-plugging (See the HDD hot-plug guidelines in “Understanding
Hot-Plug Limitations and Conditions Within the BIOS RAID Configuration
Utility” on page 66.)
■ Event logging and broadcasting, including email and SNMP messages
■ The Sun StorageTek RAID Manager GUI, a BIOS-based utility, and a command-
line interface for creating and managing RAID arrays
■ Support for disk drive enclosures with SES2 enclosure management hardware
■ A battery backup module
Array-Level Features
Note – These features are supported by some operating systems but not others. For
more information, refer to the Sun StorageTek RAID Manager Software User’s Guide or
online Help.
■ Support for RAID levels 0, 1, 1E, 10, 5, 5EE, 50, 6, 60, simple volume, spanned
volume, and RAID volume
■ Support for hot-spares (global and dedicated)
■ Support for automatic failover, so arrays are automatically rebuilt when a failed
disk drive is replaced (applies to redundant arrays in SES2- or SAF-TE-enabled
disk drive enclosures
only)
■ Optimized disk utilization, which ensures that the full capacity of all disk drives
can be used, even if the disk drives vary in size
■ Online capacity expansion, so you can increase the capacity of an array without
recreating it
- Sun StorageTekSAS RAID HBA 1
- Contents 3
- ▼ To View the Event Log 78 8
- Contents ix 9
- Declaration of Conformity 115 10
- Index 131 10
- Before You Read This Document 11
- Related Documentation 12
- Training 13
- Documentation Comments 13
- HBA Overview 15
- HBA Features 16
- Component Layout 17
- Requirements 19
- System Interoperability 20
- Server Support 21
- Software Support 21
- Observing ESD and Handling 23
- Precautions 23
- Installation Task Map 26
- ■ ESD wrist strap 28
- SPARC System 30
- Installing the HBA 31
- Connecting Disk Drives 33
- Testing the HBA Installation 34
- No Logical Drives Found 38
- Next Steps 39
- Removing the Hardware 39
- ▼ To Remove the HBA 40
- Creating an Array 42
- Making the Array Bootable 45
- Setting the Boot HBA 45
- Install the Solaris OS 48
- ▼ To Create a Logical Drive 49
- # ./arcconf GETCONFIG 1 LD 51
- # devfsadm 51
- Array on an x64 System 53
- Preparing to Install an OS 54
- ■ “Next Steps” on page 47 59
- Installing the Solaris OS 60
- Operating System 63
- Linux OS 64
- Known Issues 67
- BIOS Utility Issues 68
- Performance Issues 68
- Chapter 8 Known Issues 55 69
- Configuration Rules 71
- ■ Maximum length of 1 meter 72
- HBA Specifications 73
- Environmental Specifications 74
- DC Power Requirements 74
- Current Requirements 74
- Performance Specifications 74
- Connector Pin Definitions 75
- SATA Pin-Out 76
- SATA Power Pin-Out 77
- Introduction to the BIOS RAID 80
- Configuration Utility 80
- Hot-Plug Addition Conditions 81
- Conditions 81
- ▼ To Start the ACU 84
- ■ Delete an array 85
- Settings 87
- General HBA Settings 88
- Select Utility 89
- Utilities 90
- ▼ To View the Event Log 92
- Troubleshooting 93
- Silencing the Alarm 94
- Appendix D Troubleshooting 81 95
- Best Practices 97
- Making New Connections 98
- Enclosures 99
- Failure Conditions 99
- Failures 100
- Discovering Drives 101
- Order of Logical Drives 101
- RAID Logical Devices 102
- Appendix E Best Practices 89 103
- Selecting the Best RAID Level 105
- Understanding Drive Segments 106
- Nonredundant Arrays (RAID 0) 106
- RAID 1 Arrays 107
- RAID 1 Enhanced Arrays 108
- RAID 10 Arrays 109
- RAID 5 Arrays 110
- RAID 5EE Arrays 111
- RAID 50 Arrays 112
- RAID 6 Arrays 114
- RAID 60 Arrays 115
- Migrating RAID Levels 116
- APPENDIX 117
- About SAS 118
- About Phys 119
- About SAS Ports 120
- About SAS Addresses 120
- About SAS Connectors 121
- About SAS Cables 121
- About SAS Connection Options 122
- SAS Expander Connections 123
- Declaration of Conformity 129
- Safety Precautions 131
- Battery Warning 132
- System Unit Cover 133
- Rack System Instructions 133
- Laser Compliance Notice 133
- CD and DVD Devices 133
- Mesures de sécurité 133
- Symboles 134
- Modification du matériel 134
- Conformité SELV 134
- Couvercle de l'unité 135
- Périphériques CD et DVD 135
- Vorschriften 136
- Anschluss des Netzkabels 137
- Warnung bezüglich Batterien 137
- Gehäuseabdeckung 137
- Anweisungen zur Rack-Montage 137
- Normativas de seguridad 138
- Class 1 Laser Product 140
- Luokan 1 Laserlaite 140
- Klasse 1 Laser Apparat 140
- Laser Klasse 1 140
- FCC Class B Notice 143
- GOST-R Certification Mark 144
- Index 133 147
Související produkty a manuály pro Periferní ovladače Adaptec SAS RAID Controllers
Periferní ovladače Adaptec 4000SAS Uživatelská příručka
(134 stránky)
(134 stránky)
Periferní ovladače Adaptec 5405Z Uživatelská příručka
(136 stránky)
(136 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce