Adaptec 2910C - AHA Storage Controller Fast SCSI 10 MBps Uživatelský manuál stáhnout pdf (Strana 151)

5-15

IBM OS/2 Installation

[xxxxx07c] Unable to allocate memory

[xxxxx07d] Unable to allocate memory

[xxxxx07e] Unable to allocate memory

[xxxxx07f] Unable to allocate memory

This indicates that there may be a problem with the amount of

memory installed in your system. Verify that your system has at

least the minimum amount of memory required by your operating

system.

❒

1 2 ... 146 147 148 149 150 151 152 153 154 155 156 ... 189 190

P2B-D / P2B-DS 1
USER’S MANUAL 1
USER'S NOTICE 2
ASUS CONTACT INFORMATION 3
CONTENTS 4
FCC & DOC COMPLIANCE 6
I. INTRODUCTION 7
II. FEATURES 8
Board Layout 10
III. INSTALLATION 10
III. INSTALLATION 11
Jumper Settings 13
P2B-D/DS CPU Settings 14
(Default) 15
JP18 JP18 15
SDRAM DIMM (8 chips, Non-ECC) 17
NOTE: Insert the 20
P2B-D/DS IDE Activity LED 29
Chassis Signal 31
Ultra2 Devices 33
Single-Ended Devices 33
P2B-D/DS SB-Link™ Connector 34
IV. BIOS SOFTWARE 36
IV. BIOS SOFTWARE 39
V. SUPPORT SOFTWARE 58
VI. DESKTOP MANAGEMENT 59
VII. ASUS LAN Card 63
VIII. ADAPTEC SCSI SELECT 65
IX. ADAPTEC EZ-SCSI 67
Adaptec 7800 Family 75
Manager Set 75
Canadian Compliance Statement 77
Contents 79
4 Novell NetWare Installation 80
5 IBM OS/2 Installation 80
6 SCO UNIX Installation 81
7 SCO UnixWare Installation 81
Troubleshooting 7-11 82
Problems and Solutions 7-11 82
Error Messages 7-11 82
Introduction 83
Device Drivers 84
Requirements 87
Microsoft Windows NT 89
Updating Windows NT 4.0 95
Caution: 96
\Parameters\Device 97
Removing a Host Adapter 100
Adaptec 7800 Family Manager 102
Swapping a Host Adapter 103
Troubleshooting 104
Error Codes 105
[xxxxxd4] 108
[xxxxx0d6] 108
Microsoft Windows 95 109
Installation 109
Already Installed 110
Novell NetWare Installation 117
NetWare v3.1x 118
NetWare v4.0 or v4.1x 119
Installed 120
Bit Mask Options 128
Sample Load Commands 128
Using Removable Media 129
Mount Status 130
Lock Status 130
Verify ( 130
driver only) 130
Using the NetWare Tape Backup 131
Using a CD-ROM with NetWare 132
Optimizing Performance 133
IBM OS/2 Installation 137
Using Command Line Options 144
Adapter ID 145
Unit Parameters 145
Command Line Examples 147
SCO UNIX Installation 153
SCO OpenServer 3.0 154
Installing SCO OpenServer 5 156
Perform a System Backup 158
Use the Install Package 159
Modify the mscsi File 160
Rebuild the UNIX Kernel 161
Boot the New Kernel 162
Using Multiple Host Adapters 162
Changing the Boot Disk 162
Examples 164
Error Messages 169
/etc/conf/pack.d/alad/space.c 170
SCO UnixWare Installation 171
UnixWare 172
Back Up the Computer 174
Load the Package 174
Modify the New System File 176
Using Tunable Parameters 178
Removing the Driver 179
▼ ▼ ▼ ▼ 187

Komentáře k této Příručce

Žádné komentáře

Adaptec 2910C - AHA Storage Controller Fast SCSI 10 MBps Uživatelský manuál Strana 151

Komentáře k této Příručce

Související produkty a manuály pro Základní desky Adaptec 2910C - AHA Storage Controller Fast SCSI 10 MBps