Adaptec 2910C - AHA Storage Controller Fast SCSI 10 MBps Uživatelský manuál Strana 149
- Strana / 190
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5-13
IBM OS/2 Installation
[xxxxx081] Adapter software initialization failure
An error has occurred while the driver was setting up its internal
data structures. Verify that your adapter is supported by this version
of the driver.
[xxxxx082] Internal driver error
An error has occurred while the driver was setting up its internal
data structures. Try installing the most up-to-date version of the
driver available from the Adaptec Web site or BBS.
[xxxxx083] Adapter not supported by this version of the driver
Your adapter is not supported by the driver on your system. You
may have installed a new adapter and have not updated the driver
on your system.
[xxxxx084] Adapter software initialization failure
An error has occurred while the driver was setting up its internal
data structures. Try installing the most up-to-date version of the
driver available from the Adaptec Web site or BBS.
[xxxxx085] Unable to allocate memory
This indicates that there may be a problem with the amount of
memory installed in your system. Verify that your system has at
least the minimum amount of memory required by your operating
system.
[xxxxx087] Internal driver error
An error has occurred while the driver was setting up its internal
data structures. Try installing the most up-to-date version of the
driver available from the Adaptec Web site or BBS.
[xxxxx088] Adapter software initialization failure
An error has occurred while the driver was setting up its internal
data structures. Try installing the most up-to-date version of the
driver available from the Adaptec Web site or BBS.
[xxxxx089] Unable to allocate memory
This indicates that there may be a problem with the amount of
memory installed in your system. Verify that your system has at
least the minimum amount of memory required by your operating
system.
- P2B-D / P2B-DS 1
- USER’S MANUAL 1
- USER'S NOTICE 2
- ASUS CONTACT INFORMATION 3
- CONTENTS 4
- FCC & DOC COMPLIANCE 6
- I. INTRODUCTION 7
- II. FEATURES 8
- Board Layout 10
- III. INSTALLATION 10
- III. INSTALLATION 11
- Jumper Settings 13
- P2B-D/DS CPU Settings 14
- (Default) 15
- JP18 JP18 15
- SDRAM DIMM (8 chips, Non-ECC) 17
- NOTE: Insert the 20
- P2B-D/DS IDE Activity LED 29
- Chassis Signal 31
- Ultra2 Devices 33
- Single-Ended Devices 33
- P2B-D/DS SB-Link™ Connector 34
- IV. BIOS SOFTWARE 36
- IV. BIOS SOFTWARE 39
- V. SUPPORT SOFTWARE 58
- VI. DESKTOP MANAGEMENT 59
- VII. ASUS LAN Card 63
- VIII. ADAPTEC SCSI SELECT 65
- IX. ADAPTEC EZ-SCSI 67
- Adaptec 7800 Family 75
- Manager Set 75
- Canadian Compliance Statement 77
- Contents 79
- 4 Novell NetWare Installation 80
- 5 IBM OS/2 Installation 80
- 6 SCO UNIX Installation 81
- 7 SCO UnixWare Installation 81
- Troubleshooting 7-11 82
- Problems and Solutions 7-11 82
- Error Messages 7-11 82
- Introduction 83
- Device Drivers 84
- Requirements 87
- Microsoft Windows NT 89
- Updating Windows NT 4.0 95
- Caution: 96
- \Parameters\Device 97
- Removing a Host Adapter 100
- Adaptec 7800 Family Manager 102
- Swapping a Host Adapter 103
- Troubleshooting 104
- Error Codes 105
- [xxxxxd4] 108
- [xxxxx0d6] 108
- Microsoft Windows 95 109
- Installation 109
- Already Installed 110
- Novell NetWare Installation 117
- NetWare v3.1x 118
- NetWare v4.0 or v4.1x 119
- Installed 120
- Bit Mask Options 128
- Sample Load Commands 128
- Using Removable Media 129
- Mount Status 130
- Lock Status 130
- Verify ( 130
- driver only) 130
- Using the NetWare Tape Backup 131
- Using a CD-ROM with NetWare 132
- Optimizing Performance 133
- IBM OS/2 Installation 137
- Using Command Line Options 144
- Adapter ID 145
- Unit Parameters 145
- Command Line Examples 147
- SCO UNIX Installation 153
- SCO OpenServer 3.0 154
- Installing SCO OpenServer 5 156
- Perform a System Backup 158
- Use the Install Package 159
- Modify the mscsi File 160
- Rebuild the UNIX Kernel 161
- Boot the New Kernel 162
- Using Multiple Host Adapters 162
- Changing the Boot Disk 162
- Examples 164
- Error Messages 169
- /etc/conf/pack.d/alad/space.c 170
- SCO UnixWare Installation 171
- UnixWare 172
- Back Up the Computer 174
- Load the Package 174
- Modify the New System File 176
- Using Tunable Parameters 178
- Removing the Driver 179
- ▼ ▼ ▼ ▼ 187
Související produkty a manuály pro Základní desky Adaptec 2910C - AHA Storage Controller Fast SCSI 10 MBps
Základní desky Adaptec 2944UW - AHA Storage Controller UW SCSI 40 MBps Servisní příručka
(53 stránky)
(53 stránky)
Základní desky Adaptec AHA-3940 Uživatelská příručka
(102 stránky)
(102 stránky)
Základní desky Adaptec 3940AUW Uživatelský manuál
(128 stránky)
(128 stránky)
Základní desky Adaptec 1045 Uživatelská příručka
(69 stránky)
(69 stránky)
Základní desky Adaptec AHA-2742 Uživatelská příručka
(118 stránky)
(118 stránky)
Základní desky Adaptec AHA-1744 Instalační příručka
(191 stránky)
(191 stránky)
Základní desky Adaptec AVA-2825 Uživatelská příručka
(110 stránky)
(110 stránky)
Základní desky Adaptec AHA-1540B Instalační příručka
(14 stránky)
(14 stránky)
Základní desky Adaptec AHA-2742 Instalační příručka
(25 stránky)
(25 stránky)
Základní desky Adaptec AHA-3940 Uživatelská příručka
(102 stránky)
(102 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce