Adaptec AFW-1430 Uživatelský manuál

CardBus FireWire Enabler for DOS Copyright © APSoft, 2004 - 2005

APSoft 10 CardBus FireWire Enabler for DOS Note: For I/O and memory pools Enabler use preferable resource from bottom up (in other words, minimal pos

CardBus FireWire Enabler for DOS 11 3 C H A P T E RCommand Line Options. Command line options can be specified in any order

APSoft 12 CardBus FireWire Enabler for DOS Diagnostics and Fine-tuning /F=filename Specifies the initialization file pathname. By default the initia

APSoft CardBus FireWire Enabler for DOS 13 /IB:B:D:F, <use> Ignore PCI-2-PCI bridge. This switch may be used for subtractive-decode PCI-2-PCI b

APSoft 14 CardBus FireWire Enabler for DOS ASPI Management /NA Skip ASPI initialization. In this case Adaptec ASPI manager and driver for your device

CardBus FireWire Enabler for DOS 15 4 C H A P T E RInitialization File The initialization file is a text file that contains

APSoft 16 CardBus FireWire Enabler for DOS These parameters define the CardBus or PCI-to-PCI bridge memory filter base and limit (or size) both memor

APSoft CardBus FireWire Enabler for DOS 17 Control setting of VGA Enable bit in Bridge Control Register. Valid values are 0 and 1. Example: VGAEnabe

APSoft 18 CardBus FireWire Enabler for DOS if physically subtractive). ‘AUTO’ means that bridge’s decoding mode should be read out of bridge. Exampl

APSoft CardBus FireWire Enabler for DOS 19 resources (e.g. resources used by Legacy ISA devices). Such undetected resources may cause resource confli

APSoft ii CardBus FireWire Enabler for DOS Copyright Notice and Disclaimer Unless otherwise noted, this document and the information herein disclose

APSoft 20 CardBus FireWire Enabler for DOS MEM = 0xE1000, 0x2000, E ; Include [0xE1000-0xE2FFF] [Resources] XMEM = 0xD0000, 0x400 ; Exclude memo

A P P E N D I X CardBus FireWire Enabler for DOS 21 Additional information How to get Technical Support for CardBus Fire

APSoft 22 CardBus FireWire Enabler for DOS Example of INI file Following sample shows an example of FWENAB initialization file for the system with on

APSoft CardBus FireWire Enabler for DOS 23 This page is intentionally blank.

CardBus FireWire Enabler for DOS 24 CUSTOMER LICENSE AGREEMENT APSoft thanks you for selecting one of their products for your computer. This is the

APSoft CardBus FireWire Enabler for DOS iii Table of Contents Introduction...

APSoft iv CardBus FireWire Enabler for DOS Example of INI file... 2

APSoft CardBus FireWire Enabler for DOS v Introduction This manual provides an overview of the CardBus FireWire Enabler for DOS. All released version

APSoft vi CardBus FireWire Enabler for DOS User may freely assign drive letters to partitions, except if Enabler is loaded from CONFIG.SYS. Number of

CardBus FireWire Enabler for DOS 7 1 C H A P T E RInstallation The Enabler may be installed either in CONFIG.SYS, AUTOEXEC.

APSoft 8 CardBus FireWire Enabler for DOS You can invoke CardBus FireWire Enabler in the any point. For example: SWITCHES = /F BUFFERS = 10,0 FILE

CardBus FireWire Enabler for DOS 9 2 C H A P T E RResource management. During the loading Enabler collects information abou