Adaptec 2100S - SCSI RAID Controller Uživatelská příručka Strana 71
- Strana / 135
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
3-26
Storage Manager
Battery Backup Configuration Window – Adaptec 3200S/
3210S/3400S/3410S Only
This option enables you to view the status of the battery backup
module, as shown in Figure 3-13, and set operating parameters
when the battery capacity reaches a predetermined level.
The battery status and available backup capacity (in hours) is
displayed. You can use the Backup Capacity Warnings options to set
a threshold for entering Write-Through mode and issuing failure
warnings when the battery charge drops below the defined level.
Note: During the initial calibration or maintenance cycle for
a battery backup module, the controller operates in Write-
Through mode to ensure data is always written to the array.
Figure 3-13. Battery Backup Configuration Window – SCSI
- STORAGE MANAGEMENT 1
- SOFTWARE USER’S GUIDE 1
- Storage Management Software 2
- Copyright 3
- Trademarks 3
- Disclaimer 3
- Contents 7
- 3 Storage Manager 8
- Storage Management 10
- Software Overview 10
- ■ SuSE Linux 6.4 and 7.0 11
- ■ SCO UNIX/Unixware 11
- Storage Manager on ROM 12
- Overview 13
- Keyboard Reference 14
- Menu Reference 15
- Icon Reference 17
- Screen Layout 17
- The Menu Bar 18
- The Left Pane – Tree View 18
- Running SMOR 20
- Controller BIOS Settings 21
- Enable Bootable CD-ROMs 22
- DOS/Windows 3.1 Cache Setting 22
- Scan Delay (SCSI only) 23
- EBDA Relocation 23
- Enable Extended Int13 23
- Information Tab 24
- Configuration Tab 26
- Mem Address, IRQ 27
- PCI MWI Enable 27
- Boot Enable 27
- Bus Configuration Tab 28
- Transfer Rate (SCSI only) 30
- Termination (SCSI only) 30
- TERMPWR (SCSI only) 30
- Device Information Tab 31
- Setting the Configuration 36
- Array Operations 37
- RAID 1 BuildOption: 39
- Delete array 40
- Hot Spares 41
- Rebuilding a Failed Array 42
- Creating a SMOR Boot Disk 45
- Installing Storage Manager 49
- Running Storage Manager 50
- Physical Configuration View 51
- Logical Configuration View 53
- Logical Device Addresses 55
- Array Groups 57
- Configuration View window 59
- Creating an Array Group 61
- Naming an Array Group 64
- Requirements and Restrictions 65
- Expanding an Array Group 66
- Status Reporting 68
- Information Windows 69
- 3210S/3400S/3410S Only 71
- Flash Configuration Window 74
- Device Information Window 76
- Device Configuration Window 78
- Event Log 80
- Event Broadcaster 82
- ■ Windows 2000 and Windows NT 83
- ■ NetWare 4.2 and 5.x 83
- Windows NT & Windows 2000 84
- Formatting Drives – SCSI only 89
- Drive Failures 90
- Rebuilding a Degraded Array 91
- Assigning Hot Spares 92
- Running a Verify Process 93
- Controller I/O Statistics 94
- Cache Statistics 96
- Command Statistics 96
- Device I/O Statistics 96
- Remote Communication 99
- Client Workstations 100
- Storage Manager 103
- Windows 95/98/ME 103
- Novell NetWare 103
- SCO UNIX 103
- Connecting to Remote Systems 104
- Making a Manual Connection 106
- Using the Phonebook 107
- Using a Custom Connection 108
- RAIDUTIL Command Line 109
- Exit Status 110
- Device Address Syntax 110
- Command Line Switches 111
- Miscellaneous 112
- -D Delete logical drives 113
- Array Modification 114
- RAID Operation 115
- Controller-Specific 116
- Hot Spare Control 117
- -A Alarm status and control 118
- -L List devices 119
- -P Pagination output 120
- -q Quiet mode 120
- Introduction 121
- Management Information Base 122
- Management Console 122
- Adaptec MIB Information 123
- What’s Included 125
- System Requirements 126
- Management Consoles 126
- SNMP Architecture 128
- Adaptec SNMP Subagent 129
- Adaptec CI 132
- Installing DMI Support 133
- Adaptec DMI Modules 133
- © 2000, 2001 Adaptec, Inc 135
Související produkty a manuály pro Software Adaptec 2100S - SCSI RAID Controller
Software Adaptec ICP5085BL Uživatelský manuál
(33 stránky)
(33 stránky)
Software Adaptec AHA-1540CP Uživatelská příručka
(120 stránky)
(120 stránky)
Software Adaptec ICP5085BL Uživatelský manuál
(36 stránky)
(36 stránky)
Software Adaptec ICP5085BR Uživatelský manuál
(2 stránky)
(2 stránky)
Software Adaptec ASR-51645 Uživatelská příručka
(10 stránky)
(10 stránky)
Software Adaptec CDP-00276-01-A Uživatelská příručka
(45 stránky)
(45 stránky)
Software Adaptec ANA-6911A/TX Instalační příručka
(74 stránky)
(74 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce